Zero 80ZC Instrukcje Operacyjne Strona 1

MODEL 80ZC ZERO CLEARANCE CABINET FOR USE WITH FIREPLACE MODEL 80 ONLY RESIDENTIAL INSTALLATION ONLY Contact your insurance company for coverage an

Page 8 FRAMING CONSTRUCTION AND INSTALLATION CHOOSING 80ZC CABINET INSTALLATION LOCATION Except as noted, the 80ZC can be installed almost anywher

Page 9 CONTINUED FRAMING AND INSTALLATION INSTALLING TOP AND SIDE PANELS TO 80ZC 1. Remove the 80ZC from box and pallet. Lay brass louvers, insul

Page 10 CONTINUE FRAMING AND INSTALLING INSTALLING INSULATION TO 80ZC 1. Take (1) one piece insulation 8" X 11 1/2" place in middle front

Page 11 FIGURE 11 CONTINUED FRAMING AND INSTALLATION INSTALLING 80ZC CABINET FLAT ON THE FLOOR Framing must be accomplished after the Mod

Page 12 CONTINUED FRAMING AND INSTALLATION FLOOR PROTECTOR OR FINISHED HEARTH EXTENSION FLAT ON THE FLOOR You must use a non-combustible ma

Page 13 1-A First safety shield for millboard hearth extension in front of raised base and under floor protector or finished hearth extension 1-B

Page 14 CONTINUED FRAMING AND INSTALLATION FLOOR PROTECTOR OR FINISHED HEARTH EXTENSION WITH OPTIONAL RAISED BASE You must use a non-combustible

Page 15 WARNING: Do not pack required air spaces on top of cabinet or around pipe starter section with insulation or other materials. Top Standof

Page 16 ELECTRICAL INSTALLATION NOTE: 80ZC is not prewired, an electrician must wire the cabinet into the home wiring system using No.1

Page 17 CAUTION: Maintain a 2" air space between the rear and side of cabinet to combustible materials. FIGURE 17 MIN 2” MIN 2” MIN 2” MIN

Page 18 FRAMING CONSTRUCTION EXTERIOR ROOF OR CHASE WARNING: Install the hearth protector or finished hearth extension only as specified. The exten-s

Page 19 FRAMING CONSTRUCTION CORNER LOCATION WARNING: Install the hearth protector or finished hearth extension only as specified. The exten-sion mu

Page 20 FRONT SCREWS LEFT SIDE FRONT SCREWS RIGHT SIDE HEATER RUNNER STOPS Buck FRONT VIEW 80ZC CABINET CONTINUED FRAMING AND INSTALLATION

Page 21 Buck SLIP COLLAR FLUE EXIT SLIP COLLAR NUTS SLIP COLLAR NUTS FIGURE 23 Buck 3 3/4” X 28 3/8” OPENING FRONT C L BR

Page 22 DIMENSION (A) CONTINUED FRAMING AND INSTALLATION 13. Finish the wall around the 80ZC using brick, rock, sheetrock, paneling or any t

Page 23 CLEANING THE UNIT A. The unit should be lightly sanded with fine sandpaper or steel wool, then repainted or touched up with high temperatur

Page 24 PREVENTIVE MAINTENANCE/ SAFETY PRECAUTIONS CHIMNEY A. The chimney should be cleaned as necessary to remove creosote, soot, leaves, birds nes

Page 25 NEW BUCK CORPORATION (NBC) "LIMITED WARRANTY" FOR THE BUCK STOVE PLEASE READ THIS WARRANTY CAREFULLY PRODUCTS COVERED This warran

If for any reason you are dissatisfied with the suggested procedures, you may contact us in writing at: New Buck Corporation Custom

TABLE OF CONTENTS Cabinet Identification ...

Page 2 MODEL 80 ROOM HEATER AND MODEL 80ZC CABINET IDENTIFICATION 1. 8" Flue Exit 2. Hot Air Vent 3. Catalyst Probe 4. By Pass Damper &

Page 3 RESIDENTIAL INSTALLATION Listed NEW BUCK CORPORATION: Model 80ZC Zero Clearance Cabinet Assembly for use with Model 80 only.

Page 4 INSTALLATION PRECAUTIONS The following precautions are mandatory for a safe installation. (A) Compliance with local building codes and regul

Page 5 SELECTING A CHIMNEY INSTALLATION AND LOCATION There are two basic types of chimney installation possible with the 80ZC; straight up through a

Page 6 B. Exterior Chase Installation: (See Figure 4). A chase is an enclosure built specifically to house a chimney

Page 7 Floor Protection: or Hearth Protector Floor protection must be 3/8” minimum thickness non-combustible material or equivalent. How to use a